Using Electric Barbecue On Outdoor Outlet With Shared Load

I recently purchased the Meco 9359 electric BBQ since I cannot have gas or charcoal grills in my condo. The instructions recommend plugging into an outlet with at least 15 amps. The grill itself has a 1500 watt rating. The outlet on my deck (15 amps) is shared with the 2nd bedroom, the bathroom and one outlet in the kitchen. Out of all these recipticles, the one in the kitchen is the only one with something plugged into it (an emergency flashlight that lights up when the power goes out). The



My father, God love him, sometimes cries Armageddon when things aren't 100% perfect in his eyes and is recommending that I return the grill. Is there an inherit danger using this grill in the outdoor outlet based on what I've listed? The outside outlet is not GFCI, would replacing it with one help?
      


Similar Tutorials

How to Lay Sod - The Right Way!
   - Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
   - This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
   - If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ...


Similar Topics From Forums

OK, I'm an electrical dummy ...



I have finished basement w/a bathroom. We have an ejector pump off the bathroom that has been plugged into an outlet w/gfi since I've owned the house (10 years). There is also a booster fan for my electric dryer plugged into the outlet (has been the same for 10 years).  The only thing that has ever tripped up that outlet is using a hair buzzer in another outlet within the bathroom (but once you hit the reset its fine).

   

  This morning I realize the ejector pump was not sucking down the water from the drains. I looked at the outlet and realized it needed to be reset. When I reset it, the pump would run for a few seconds and the outlet would trip up again. Tried this a few times. Thought maybe it was an issue w/the outlet altogether. Neighbor suggested maybe it was an issue with the pump. Went thru various scenarios and bottom line is when I plug the pump into other outlets it works totally fine and once I do that and reset the outlet it was on, the booster fan works fine and the outlet does not trip. So, basically this outlet is tripping when the pump is on it but the pump is not tripping other outlets and the outlet works fine as long as the pump is not on it.

   

  What could be causing this? Why would an outlet that housed the two things on it all of a sudden continue to trip when the pump is on it but the pump is fine on its own in another outlet and the outlet is fine on its own w/o the pump?
      
We just got a used hot tub.  It ran fine where we purchased it but since we got it home, it has not run.  We installed a new breaker for the hot tub and an GFCI outlet outside.  The hot tub inself has a GFCI installed on it.  If we plug it into the GFCI outlet it runs for a few seconds and either trips the circuit inside or the hot tub.  Is it necessary to have a GFCI outlet outisde if the hot tub has one?  We are thinking that this may be our problem..redundancy.  Can we install a regular outlet outside instead of the GFCI outlet?  When we plug it into a regular outlet it runs.  We want to make sure that this is safe before proceeding.
      
We are just beginning to start with our kitchen remodel. Today, I mapped out all the circuits and this is what I found.



Circuit # 7 - 20 amp circuit to 1 back splash outlet then to 3 kitchen wall outlets, then to a closet outlet and closet ceiling light and then to a side  porch light!



Circuit # 8 - 20 amp to Dishwasher and Disposal



Circuit # 9 - 20 amp circuit to microwave and kitchen ceiling lights. 2 patio recessed lights and dining room ceiling light.



Circuit # 12 - 20 amp circuit to another back splash outlet then to 2 dining room wall outlets.



Circuit # 14 - 20 amp to Refrigerator only



Circuit # 18 - 15 amp to GFCI outlet in garage then that feeds 3 outlets for 3 bathroom outlets and 1 outside patio outlet.



I going to have to add 1 more back splash outlet due to increase in counter space. I'll put the microwave on a dedicated circuit. So I need 2 additional breakers but I only have 1 blank spot in the breaker panel. I guess I can add one of those slim tandem breakers.



So my question, is it ok to have additional wall outlets on the same circuit as a back splash outlet?  If it's ok I'll lighten up circuit # 7 by putting some of those wall outlets on the additional back splash outlet.

Oh, I have 2 20 amp circuits I did not get identified yet! I'll get to those tomorrow.



thanks!
      
Trying to install a replacement floor outlet. I have a lew electric (RRP-1-NPR); It appears that the holes for the faceplate screws are aligned over the same holes that would secure the outlet to the floorbox. The previous outlet cover had 2 sets -- one to secure the outlet to the floorbox, and another set to secure the cover to the outlet, like you'd see with any other lightswitch or outlet. So now the outlet is loose within the floorbox -- what am I missing?

thanks
      
I'm in the process of planning to wire up two spot lights on the face of my deck as well as running an outlet (which will also be under the deck) for a LV transformer to plug in to. I will need a few junction boxes to achieve this, as well as electrical boxes for the two spot lights. I'm planning on running 12AWG THWN through some sort of conduit run along the joists to the various lighting locations and junction boxes. This will be between 3' to 8' above the surface of the ground and under roof for the most part (we built a roof over the majority of the deck as well).



So, do you recommend PVC and plastic boxes or EMC and the appropriate boxes?
      
I am thinking of purchasing a WineKoolr used but after looking at the manual online it states that it must be plugged into a "Dedicated separately fused, grounded, 15 amp 100-120v line." The price I can get this at is awesome, but I live in apartment and am not sure, but think I only have 1 dedicated line at all, for the fridge. The previous owners said they just had it plugged into a normal outlet fine, but I want to know if it is a serious issue to do this? I really want a nice cooler for my beer cellar since I have no actual basement, so I am really hoping I can make this work in my home. Thanks for any help!





*Someone asked me on another forum what breakers I have for where I want to install it, and its in my second bedroom.  The breaker for those outlets is a 15A.  They also said that it probably says that in the manual to cover themselves legally but I should likely be just fine.





**

Well I turned off the breakers until I found which was for the outlets in the spare room.  As far as I can tell, the only things on this circuit are the spare bedroom outlets (not the lights), and 1 outlet in the hallway.  Nothing is plugged into any of these and its a 20A circuit.
      
I am new to the forum so kindly bear with me.  I live in Mesa, AZ and have just had a PEX repipe done to bypass my copper hot water lines.  (God don't ask!  A real problem here with slab foundations.  I already had my kitchen jack hammered once.  It is NOT pretty!).

It seems really odd to me that just because it is a dedicated circuit  that code would not require that circuit to be GFCI protected.

I have a dedicated 20 amp duplex 12 AWG wire outlet under the sink and it is within a few inches of the water lines.  The outlet serves a switch for the garbage disposal and serves my dishwasher which is always hot. 

  Now that I have all my maple cabinets pulled out I thought I might change the outlet to a GFCI just to be safe.  I have a ground wire, a red wire, a black wire and a white wire.  As it is dedicated I think I should use the LINE sided instead of the LOAD side but I am not sure where the wires should go.

Could someone give me info on this?  It would be greatly appreciated.  Thank you.
      
Having a brain freeze, if someone could take a moment to explain this to me, it would be greatly appriciated. I am wiring four recessed lights in a bedroom, off one switch. I am going to grab power off an outlet. Does the power have to go into the switch box first and then out to the first light? and then on to the others? Can I get power from an outlet and then wire each of the lights and bring the last one to the switch box? I dont want the switch to control the outlet, just the recesed and I am trying to determine where I can get the power from and if it has to go into the switchbox? I am drawing a blank.

Thanks!
      
I have this cirucit with a GFCI outlet, then two regular outlets off the load.  None of them work.  The GFCI reset button was out, push it in, it pops back out. 



I replaced the GFCI with a new one and it seems to be fine.  (GFCI outlet and load outlets are working).



Is this common?  (I mean that a GFCI would go bad, and display this for behavior?)



Thank you, and if this is a stupid question, you may electronically "dope slap" me!
      
I have a home that I only use from time to time.  At Christmas one of the GFCI outlets kept tripping.  This outlet has a TV/reciever/cable box/xbox/lights, etc. on the load side.  When I reset it, everything would be OK for 20 minutes or so, then it would trip.  I did not have time to investigate the problem so I just left it.  When I returned a week or so ago, the outlet was tripped and would not reset.  As soon as I pushed the reset button in, it would pop back out.  I replace the GFCI outlet but that did not help.  I removed all load outlets and inspected them.  Everything looked OK.  Anyone have an idea.  The strange thing to me is that the problem seemed to get worse over time.  (I.e. it stayed reset for 30 minutes at Christmas and now it will not reset at all).  Ideas?  Thanks in advance.