Wiring Some New Can Lights

I just ordered some Arlington Siding Mount Kits with built in electrical boxes to install some lights on the outside of my garage. 



So, the issue is, the mount kits' built in electrical boxes are only 6.8 cu each and I'm wiring the lights up with two 3-way switches.  The source is at the first switch, then on to the two lights and then to the second switch.  There is not enough room to do the splices and connection in the built in boxes (I'm using 12awg, but even if used 14 still not enough room), so my plan was to wire everything to a central junction box inside the garage between the two lights and make the appropriate connections there. 



I'm attaching my rough sketch of the planned connections (omitting ground wires).  Can you guys please confirm this is correct?    Thanks for the help!



To clarify the drawing, blue is white (neutral) and the blue with black tape coming off second switch is marked as hot.  (I'll also mark it as hot in the J-box).  Yellow Triangles are wire-nuts.
      

Hello there,



I just installed a new fixture in my dining room. It has 5 MR16 halogen bulbs. When i turn on the light switch, the lights are gradually turning on to full brightness. The process takes a between 5 to 10 seconds.



I removed one of the bulb and noticed it took a bit less time and continued until I had only 3 bulbs and then the lights are turning on instantly.



So I think its obvious that the fixture is drawing too much power from the circuit. My question is, why? What tests can I dk to find the cause? Is it a faulty switch or faulty wiring?



Thank you!
      

just wondering if someone can give me a quick answer.  I currently have 7 receptacles and 3 lights on one circuit.  the receptacles are in the living room and the lights are in the basement.  I have just installed 6 recessed lights in the living room. does anyone think that that is too much to add to the circuit.  not much gets plugged in in the living room    T.V.  couple of lamps dvd player, occasional vacuum cleaner.
      

Hello. I'm a new home owner and DIY-er. I have 3 fluorescent lights  in my basement. I just replaced the fixtures' older ballasts with new  T8 ballasts in the first two lights and they work fine. I am having  trouble with the third light's wiring to the ceiling. I cut and removed  the old ballast without paying much attention because I was able to wire  the first two lights without any problem. I connected the new ballast  to the bulb sockets in the fixture, just like I did with the first two  lights. When I went to connect the ballast's black and white power lines  to the ceiling lines, I was thrown off by a red wire, which I guess is  connected to the light switch.  In addition, this light is connected to  the one of the other fluorescent lights and both are controlled by the  switch. I have attached  pictures of how I have it wired.



The way I have it wired now,  the other light turns on and works fine when the switch is flipped.  However, this light has the bulb flicker and then not turn on. If anyone  can tell what I'm doing wrong from looking at the pictures, I'd  appreciate any help! Thanks!
      

hi everyone.



i am installing 4" recessed lighting throughout my main floor.  my house was built in the 40's and the previous owner installed drywall over the existing lath and plaster ceiling.  so I've cut a trench down the center of my room to drill floor joists to run wiring and cut my holes for the new lights.

the lights are fire rated and do not require insulated cans for a traditional installation in a drywall ceiling.



question i have is with the additional 1/2 to 3/4" of lath and plaster above the drywall, should these lights now have insulated cans or should i be fine with the cans I've got?  there is no insulation in ceiling.



any suggested would be appreciated.



thanks

d
      

I want to run a new 12/3 to wire a room added on the back of the house. One circuit will be 6 wall outlets. The other will be a ceiling fan and 4 recessed cans. Can I add 2 outdoor lights-using standard outdoor bulbs-to the same circuit as the ceiling lights? Do I use the wall switch(box properly sized) as the junction for the outlet wiring and feed to wall switch for outdoor lights?
      

I am working on fixing an issue with the wiring in one of the bedrooms in my older mountain home. Though I was not present for the cause of the problem, here is what was told to me by the tennant.  he claimed that he went to turn on the light in the closet, (a 3 lamp track bar light, wired to a switch) he heard a loud pop from the light in the closet and lost power to to the room. The room has 6 recessed ceiling lights on 2 separate switches, presently only half of the lights work.There are no breakers tripped, no obvious shorts at outlets. I have opened the drywall following the wires around hoping to find a short but I have found nothing. I decided to try something, and I bridged the working switch to a dead outlet and everything turned on. I am waiting til the daytime to follow the wires outside to the breaker box, but so far no breaks or anything.. curious if anyone has any pointers.. could the pop he heard from the track lighting have killed a breaker? its about the only thing left.
      

I'm wiring two lights to one switch with power coming into the switch. All the diagrams I see show the connection of the two lights at one of the lights(if that makes sense). Can all of the connections be made at the switch box if theres room? Basically a wire from each light and the power wire all run to the switch box and connected.
      

I am only using a simple "non-contact" voltage detector. I am getting a reading from the switch, along part of the line and then at the lights themselves, but the lights are not coming on. I have not gotten into the attic yet to check the line and junction box. What could cause this? An open connection or loose connection? Any help with troubleshooting would be great.



This is a new install of lights, they were not existing. Power is at the switch. Had single pole now I have a double switch. (the existing light that was on the single pole is still working fine). At one  point I connected just the new lights to the existing power, single pole switch, and still did not have lights.
      

can a 14 gage wire for a light be connected to a 12 gage wire?  the breaker is 20 AMP.



there is no light in a room with an outlet present, i was going to put in lights and hook up the lights with 14 gage to the 12 gage wire connecting the outlet.



or, should i be consistent and use 12 gage to connect the light?



thanks fella's