Having Trouble With Puck Lights

Hi everyone. I have puck lights that were installed under my kitchen cabinets before I moved in, and now it's time to relace a few of the bulbs. I have tried everything and I can't seem to get the darn lid off and can't. I've twisted in both directions, tried to gently pull it straight down, gently pushed up to see if something would release, etc. etc. I'm afraid of doing much else for fear of breaking the plastic or ripping the thing off the cabinet. Does anyone have any idea how these lids should come off? I'm having the problem with two different light fixtures, so it's not a random defective one. A picture is attached (at least I tried to attach it). Help is most gratefully appreciated!!



Thanks!

Renee



P.S. I know it is important to not touch the bulb directly to skin.
      


Similar Tutorials

How to Lay Sod - The Right Way!
   - Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
   - This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
   - If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ...


Similar Topics From Forums

Hi everyone,



I'm pretty new to the whole homeowning/do it yourself lifestyle, and have a question about the light fixture in my kitchen.  Recently 2 twisted cfl bulbs went out, probably within 1-2 days of each other, and I am having a hard time figuring out how to replace the bulb.  I believe the lights in my kitchen are considered recessed lighting.



So when the first light went out, I hastily grabbed my step ladder and tried to twist the bulb out.  I should have looked more closely at the fixture because when I started to twist, the bulb popped in my hand.  No big deal, just a bunch of debris all over the place.  I looked at the fixture and it said I should pull straight down to remove.  Doh!  The second light went out a day or two later and this time I pulled straight down on the bulb to remove.  To my surprise the bulb came out, but at the ends of the bulb were 2 bare wires.  I had never seen this bulb in stores before.



Anyways here are some pictures I took of my fixture.  Can anyone tell me how I am to replace my busted bulbs?  Thanks!












      
Tearing out a wall cabinet uncovered a hole in the wall which I think I can install an outlet on.  The problem is that the ground wires are to short to pull out far enough to attach to the outlet.



However, the box in the wall is metal, so there should still be an path to the ground from the outlet right?  Or is there something special about the green screw on the outlet which makes that the only safe spot to attach the ground to?



box I uncovered:

https://lh3.googleusercontent.com/-v...s538/photo.jpg



fuzzy picture of the inside of the box showing the ground being attached to metal box:

https://lh6.googleusercontent.com/-B...303_154810.jpg



The outlet I want to install... (although I dont know how to pick the right outlet based on the limited info on the wiring I have, so any help with that would also be appreciated):

http://www.homedepot.com/Electrical-...&storeId=10051
      
Hello. I'm a new home owner and DIY-er. I have 3 fluorescent lights  in my basement. I just replaced the fixtures' older ballasts with new  T8 ballasts in the first two lights and they work fine. I am having  trouble with the third light's wiring to the ceiling. I cut and removed  the old ballast without paying much attention because I was able to wire  the first two lights without any problem. I connected the new ballast  to the bulb sockets in the fixture, just like I did with the first two  lights. When I went to connect the ballast's black and white power lines  to the ceiling lines, I was thrown off by a red wire, which I guess is  connected to the light switch.  In addition, this light is connected to  the one of the other fluorescent lights and both are controlled by the  switch. I have attached  pictures of how I have it wired.



The way I have it wired now,  the other light turns on and works fine when the switch is flipped.  However, this light has the bulb flicker and then not turn on. If anyone  can tell what I'm doing wrong from looking at the pictures, I'd  appreciate any help! Thanks!
      
In a previous thread (Wire suitable for underwater usage), I enquired about what cord types would be suitable for underwater usage because I was building a submersible fishing light to attract baitfish.  Well, the light is done, and the bulb "farthest away" from the battery is by far the brightest in the chain (I hesitate to say chain since they are wired in parallel). 



Attached image "photo 1" is a picture of the light I made.  Notice the bulb all the way to the left is far brighter than the rest.



All bulbs used are the same spec, and look like this:



To wire the bulbs, I cut the flange off with a Dremel tool so that they would fit in the tube.  Two pair of them have their terminals soldered together (neg to neg, pos to pos...that's the "gap" you see in the lighting), and the first bulb in line is upside down, with it's terminals facing the incoming wiring.  The first bulb receives the wiring from the main line, then hookup wire is used to jump from those terminals to the next set, etc. 



There IS one anomaly with the final/far left bulb.  When I was cutting off the flange, I accidentally cut too far on that piece, basically severing the terminals from the bulb.  So, when wiring it into the circuit, I had to improvise and soldered the hookup wire directly into the solder points located on the bulb itself (instead of the underside).  Hopefully you can see what I'm talking about in attached "photo 2."



I have no idea why this anomaly would make the bulb brighter though.  Can anyone think of any other reason the bulb would be brighter?  Unfortunately, I cannot do any readings on the individual bulbs because I did not notice this until everything was soldered into place and the lamp sealed/waterproofed).
      
I have a home that I only use from time to time.  At Christmas one of the GFCI outlets kept tripping.  This outlet has a TV/reciever/cable box/xbox/lights, etc. on the load side.  When I reset it, everything would be OK for 20 minutes or so, then it would trip.  I did not have time to investigate the problem so I just left it.  When I returned a week or so ago, the outlet was tripped and would not reset.  As soon as I pushed the reset button in, it would pop back out.  I replace the GFCI outlet but that did not help.  I removed all load outlets and inspected them.  Everything looked OK.  Anyone have an idea.  The strange thing to me is that the problem seemed to get worse over time.  (I.e. it stayed reset for 30 minutes at Christmas and now it will not reset at all).  Ideas?  Thanks in advance.
      
Hello there,



I just installed a new fixture in my dining room. It has 5 MR16 halogen bulbs. When i turn on the light switch, the lights are gradually turning on to full brightness. The process takes a between 5 to 10 seconds.



I removed one of the bulb and noticed it took a bit less time and continued until I had only 3 bulbs and then the lights are turning on instantly.



So I think its obvious that the fixture is drawing too much power from the circuit. My question is, why? What tests can I dk to find the cause? Is it a faulty switch or faulty wiring?



Thank you!
      
We had a pipe disconnect above the downstairs bathroom and the ceiling just about came down, so I decided since it was a hedious looking space, that it was a sign from the gods: Reno time!



Im now at the wiring stage. Originally there was a junction box with a light fixture out one side and a single pole switch(no ground screw...grnd wire attached to the box)on  the other. Typical set up: white from switch marked "hot" or "black" at both ends, and spliced with the incoming power's black wire. Then remaining blacks are spliced together as are the remaining whites... grounded accordingly.



What Im trying to do now is add a GFCI receptical to the mix. But Im having some trouble figuring it all out. NOTE: light fixture is not installed yet, just the wire for it with the ends capped off with a wire nut on each of the wires (Wht/Black/Grnd)



First, whats in the walls: Circuits on a 15 AMP fuse with older (but not the oldest) 12/2 wire with a blue weaved fiber outside cover. Still looks to be in great shape. I've continued using newer, yellow (Lomex or Romex?) 12/2 from homedepot as I've read that you should not mix 14 and 12 together.

All that is on the cicuit is 3 pot lights with 65w bulbs, single bulb on the stairway and what ever goes in the bathroom, so from my math, there should be plenty of room left on the circuit.



What I've tried so far:

A: I spliced the "hot"/"black" white wire from the switch to the incoming power's black, like before. Then I spliced all remaining blacks together with a wire nut, then the same with all remaining whites and then all grounds (did not attach any grnd wire to the Junction box).



Result, Nothing. After switching on the power, I tested the GFCI with a voltage tester as well as the switch and got no read.



B: Undid everything, re-spliced all like to like: all blck together, all white together..etc.



Result: Fuse trips.



Im no electrician, which I imagine is blatantly obvious from the above post, but I am following a Homedepot wiring manual, its just that what Im trying to do is not really addressed in the book... at least not directly. So I've been trying to figure it out by reading every single page, but Im still at a loss.



I've attached a very basic diagram of what is there right now. Any advice would be most appreciated.

Thanks in advance,

John
      
Need some help solving this clicking.

So I have just installed 16 pot lights in my kitchen and dining room.

I have 8 on one circuit going directly from the panel to the switch then the switch to the pots. 15amp breaker. Same for the other 8.

The brand is hallo 4 inch and they have quick connect for the 14-2 wire. All the pots are grounded and the beaker is grounded at the panel.

So I will have the pot lights on for say 1/2 hour or so, doesn't matter what 8 I have on but once I turn them off about 2 - 10 minutes later I hear I clicking noise coming from different pots at different times. I have followed all the directions and did not overload either circuit because I have 8 cans on each.

If anyone could shed some light on this for me that would be great. I just don't know how this clicking sound can happen if the light are turned off. Never happens when they are on. Could it be that they are cooling down?.
      
I was going to put this in this thread  Junction box in stud wall behind drywall?  but, decided to start a new one.



Two nights ago while sitting in my kitchen the can lights in my soffits above my cabinets suddenly went out. At first I thought my daughter or her boyfriend was messing with me and reached around the corner and flipped the switch. Nope. Tried the other switch near me and nothing. Everything else in the kitchen worked.



Thinking tripped breaker for a moment...nope other lights work on the circuit. Can't be 6 CFL's burnd out at the same time. Hmmmmm?



Background:

Kitchen was remodeled 12 years ago. Drywall was in good shape so not removed. Added circuits for Fridge, Microwave, Garbage disposal, Stove (gas),Dishwasher, range hood, and countertop recepts. None of these are tied to lights. Original task lighting was 4' tubes over countertops above cabinets. Remodel added sofits and can lights from these two feeds



Started tracing circuit path to look for loose/broken wire. Found no power at lights. Checked power at breaker...Good. Follow wire to kitchen, no junctions. Wire disapears up into wall below the switch area. Check for power at switch box. Yep, power there. Power off and pigtail Neutral/hot  wires at a can light together. No continuity on the load side of the switch circuit. Broken wire somewhere between the switch and the lights. Fortunaly there is an attic space above the kitchen. Unfortunatly, it is a short headroom ~3' or less and full of blown ihn insulation. In I go to trace the wire.  after about 10 min up there I found the burried junction box. At some time in the past there used to be a single light in the center of the "U" shaped kitchen cabinets. This was abandoned and the box was drywalled over...still in the location for the light hookup so the cover was not readily accessable. found a tightly twisted Ground, Neutral and Hot with nuts. All looked good untill I Started messing with them. found that one of the hot leads had broken right at the insulation on the wire. Looking at it closer I could see some arc burn at the break. I am thinking that when the handy hack that did the job nicked the wire he did not know or care and tristed it together anyway. It took over, to my best guess, 20 years for it to fail.



Moral... It can happen
      
Just remodeled my kitchen and now at the point to install some under cabinet lights. I had ran an extra romex line with the intention of using it for the cabinet lights on a lutron dimmer.



I did google some forum discussions, but they were a few years old. I'm sure better products has been released since then.



Led's preferable, but will also consider xenon if they led's can not be harwired with a dimmer.  I need about 7'.



Thanks