Help With Switch Wiring

When repairing a light switch I came across this wiring in a supposed 3-way setting in my kitchen.  Two Single Pole Double Throw switches controlling a single light fixture. 



Check out the quick and dirty wiring diagram showing the way these are connected.  I believe there should be a 14/3 between the two switches right?



All I see is 14/2 coming in and a 14/2 going across to the other switch, and then a 14/2 going to the light. And why are the neutrals cut and wire capped?  This doesn't make sense to me, but the light does work from both switches.



Any insight will be greatly appreciated.



Cheers!
      

Am doing a bathroom reno and installed a new fan. Original switch was a simple on off single pole. I want to install a DewPoint condensation fan switch that will turn on automatically at a certain moisture level.

The new switch as 4 wires. green ground, red fan, black power, and white neutral. I know the ground, but how do I hook up the neutral and fan to the existing fan set up?

There is a double pole light switch in the same box that has a couple wires to it, and there is a mass of whites that I am not sure where they go



Can I hook up the neutral somewhere else, or put it with the fan like a single pole? What do I do with this?



In the attached picture the switch on the right is the 2 pole light switch and on the left is the fan switch that I hope to replace.



Your Advice is appreciated
      

I replaced an existing light switch with a switch/outlet combo.  The outlet works and switch operates light only, all appears to be working.



I plugged in a 660W device into the outlet and the light starts to flicker when the device is on, when the device is off, light stops flickering.



If I move the 660W device to an existing outlet in the same room, light does not flicker.



I don't think it should be a load issue but couldn't figure out why else the light flickers.
      

I've installed two dimmer switches in the bar area of my basement. It's the dial type, where you can push the dial in to turn the light on or off, or turn the dial to dim the light. One dimmer operates the recessed lights in the ceiling, and the other dimmer switch works a pendant light that I have over my bar. The dimmer for the recessed lights works totally fine. They turn on, off and dim. The pendant lights, on the other hand, only turn on and off. They for some reason will not dim. I checked the voltage on the pendants to see if maybe it was an issue of the switch being a high voltage dimmer operating low voltage pendants, and the pendants are 120V with 75 max wattage. I'm at a stand still. I have no idea what I'm doing wrong. Do any of you have suggestions? I took a couple pictures, not sure what good they'll do. The best I can do for a camera is my iPhone, so they're not the best quality.








      

hello

I am dealing with what seems like a strange issue with a single pole switch, and I am royally baffled even after reaching out to someone a little more knowledgeable than me.



Yesterday: Replaced with a single pole switch with an identical one that I painted (for decor reasons). Two wires were going into the old, and the same 2 wires are attached to the new one. However, the light it controls fails to come on despite light bulb being good, and outlet located 4 feet below the switch fails to operate. With voltmeter in hand I tested voltages.

At the switch: 3 wires feed into it, all whites capped together, and 2 of the 3 blacks (A,B,C) are hot with 110. A is hot and was/is connected to one of the terminals of the single pole switch. B and C (hot) are capped together with a jumper that goes to the other terminal of the single pole switch. So I am royally baffled as to why a switch would be wired with 2 hot wires going into it. I swear it has been like that since we bought the house a year ago, and the light worked fine. I simply replaced the switch with the same wiring, and now it doesnt work. I even touched both hots (A and C) independently to wire B which (using common sense) should be the load wire to the lamp, but the lamp did not come one.



Other outlets in that circuit do not work either. They get 110 to line and ground, but not across the outlet.



I hope I was clear in explaining, and I hope someone can possibly shed some light so I can resolve this.



Thank you
      

what the fudge sticks man?



I am not a DIY'er or a handy man but I gave it a shot..



I replaced an old a$$ receptacle with a brand new one and I wired it EXACTLY the same as the old one..



I know this because I did it WIRE BY WIRE!! i.e. I took 1 wire off the old receptacle and installed it on the new one.. wire by wire..



Power works and all that.. BUT NOW the ONLY light switch in the room does not control the bottom receptacle anymore?



what gives? i don't get it.. what changed?



Previously the light switch gave power to this outlets bottom plug, so I had the lamp plugged into it and turned it on/off with the light switch..



but that doesn't work?



I even triple checked my work and still not seeing whats up?





any ideas?





oNe.





p.s.  HOW do you release the wires on these new fangled outlets? It says push spring in slot to release but I am not seeing it?  any ideas?
      

I have an older Kohler whirlpool (Tea for Two) that I installed and worked fine (occasional slight delay in starting).  I shut off the breaker to work on a vanity light installation.  When I threw the breaker back on, the tub would start on its own.  At first could shut it off.  Then had to turn the breaker off to keep it from coming on spontaneously.  The only way I can use it is to turn on the breaker and then wait for it to come on.  It stops after about 20 minutes (normal I think).  But then won't restart or restarts/tries to restart later, sometimes multiple times.  I have to shut the breaker off, or it will keep going on or trying to go on.  Runs fine when it gets started.  I am thinking it is the starter button and/or a timer problem.  Any thoughts?
      

Need some help solving this clicking.

So I have just installed 16 pot lights in my kitchen and dining room.

I have 8 on one circuit going directly from the panel to the switch then the switch to the pots. 15amp breaker. Same for the other 8.

The brand is hallo 4 inch and they have quick connect for the 14-2 wire. All the pots are grounded and the beaker is grounded at the panel.

So I will have the pot lights on for say 1/2 hour or so, doesn't matter what 8 I have on but once I turn them off about 2 - 10 minutes later I hear I clicking noise coming from different pots at different times. I have followed all the directions and did not overload either circuit because I have 8 cans on each.

If anyone could shed some light on this for me that would be great. I just don't know how this clicking sound can happen if the light are turned off. Never happens when they are on. Could it be that they are cooling down?.
      

I replaced a ceiling light with a fan/light with a remote. everthing works. their is one light switch and one dimmer switch. The dimmer switch has a red wire and a black wire connected to the black wires coming out of the dimmer switch, plus a green wire hooked to the metal portion of the dimmer. My question is: Do I have to remove the dimmer switch, if so, can I disconnect the red and black and hook them together? If I have to replace the dimmer with a regular switch, what kind of switch do I get?

Thank you
      

I am working on fixing an issue with the wiring in one of the bedrooms in my older mountain home. Though I was not present for the cause of the problem, here is what was told to me by the tennant.  he claimed that he went to turn on the light in the closet, (a 3 lamp track bar light, wired to a switch) he heard a loud pop from the light in the closet and lost power to to the room. The room has 6 recessed ceiling lights on 2 separate switches, presently only half of the lights work.There are no breakers tripped, no obvious shorts at outlets. I have opened the drywall following the wires around hoping to find a short but I have found nothing. I decided to try something, and I bridged the working switch to a dead outlet and everything turned on. I am waiting til the daytime to follow the wires outside to the breaker box, but so far no breaks or anything.. curious if anyone has any pointers.. could the pop he heard from the track lighting have killed a breaker? its about the only thing left.