Crimping Flex Ends?

I have a fan assisted oven which draws about 12A maximum but the nearest socket outlet is already part of a ring main which is pretty fully loaded so I decided that it'd be best to plug it into the other ring main in my house and the nearest socket is about 15metres away, would a 2.5mm flex be ok for this or should I opt for a 4mm? Or would a 4mm have a knock on effect on something else
      

4 gang switch box. power into this box. All wire is 12 Guage.



Neutrals and hots are easy to nut together, 5 at most in 1 nut.



But what about the ground wires? There will be 9 total ends that need to be connected, 9 seems like alot under 1 wire nut.....or is it? lol



Can i make up 2 sets of grounds and use a jumper between the 2 wire nuts?



Do they make a wire nut for 6 wires?
      

I have a 50 foot hdmi cable that is hooked to my TV, run through my wall to my basement then over and upto a closet where the cable is hooked to my surround sound. Unfortunately my basement ceiling is finished in drywall and there is no access to replace the cord. To make a long story short a cable TV provider came to my house to change out a box and broke the prongs on the hdmi cable. My question is, can HDMI ends be spliced or replaced somehow without replacing the whole cable.
      

Hey guys, I am looking to find out what kind of cable this is.







Some details



It looks to me like some kind of. 



3 Conductor surface shielded Cable



The outside is a black shield



It has 3 wires: red, gold green that were twisted together and have some kind of coating on them, not rubber but a color coating on them.



Its a verrrrrrry thin cable and the wires are individually twisted with about 8 strands and then the 3 twisted and then the outside.



Anyone have by any chance of this laying around or know what this kind is?
      

My house has 240v outlet from the previous owner for a kiln of some sort. Im putting a tanning bed in its place. The plug on the tanning bed is a L6-30. I checked specs on the tanning bed and it requires a L6-30 recepticle and a 30amp circuit breaker. I went to the local home fixit store and found the correct recepticle and bought a 2-pole Siemens 30a circuit breaker. After shutting off the main breaker and using testing equipment I pulled out the 50a breaker and replaced it with the 30a..no problem. Heres where Im not sure....The L6-30 recepticle that goes in the wall has a X and a Y and a G marking on it. The G is grounding per instructions, w is white or grey, and X,Y,Z are black, red, blue or etc etc.The wires that come out of the house are red, black and a bare aluminum bradied type wire. Looking at the back from the top counterclockwise  I hooked up the red, then black, then the bare nraided to the G (has green screw) Is the black and red correct? And why doesnt it say red, black and gound?  Can anyone shed some light on this? Thanks!!!
      

I'm replacing my electric range with gas.  The electric has (I think) a four-wire #6 or #8 cable approx 60ft run with a 40a dual post breaker.  I say "I think" because the wire is behind everything else in the panel.  I see red/white/black wires, but no ground and I can't read the jacket.  Once I cut the main, i'll have a closer look. 



The gas range requires only a 15amp breaker. 

Can I simply replace the breaker with 15A and the 4 prong outlet with a Nema 5-15p?  I'd cap off both ends of the red wire.  Is there some sort of code that says I need to maintain the 40A circuit for a future stove?

Or is there some sort of transformer I can plug into the stove end and avoid all that hassel.  ?
      

I've been the owner of a 1930s era Colonial Revival that our first major project is to rewire the house. We have a 100A main box that is maxed out, a combination of cloth 2-wire, flex, and some cracking Romex along with some downright dangerous open wiring in the basement, tapped wiring in the kitchen and study, some gangboxes that were wallpapered over in the bedrooms that we assume were wall lights (we have similar wall lights in the bathrooms), inadequate outlets in most rooms, no GFI. Etc. Etc. In addition the bathrooms are small and lack wall switches or outlets (they have two pull-cord wall lamps, with one lamp with a outlet.



Here is a floor plan with electrical represented on the ground and second floor. Still working on mapping the basement and the attic (which has a 3/4 converted finished "bonus" room.



My Father-In-Law who is a licensed electrician has promised to gracefully donate a couple months of his time to rewire everything. Also a bonus in this is the majority of outlets are mounted on the baseboard trim and not in the plaster.



My plans are to go with a single 200A main, likely double the amount of outlets in each room, GFI where needed.



While I know some basics, I want to familiarize myself a bit more on what is the best approach to rewire. For instance should I look at running conduit in just one spot of the house, or should I run two on each end of the house? I plan to do some major remodeling of some rooms in the future, especially the kitchen and bath so what are the best ways to ensure I have an easier time with these remodels?
      

Hello All,

Hopefully I am posting this in the correct forum!

I am new to the forum and I have a question I would like to pose.

I am trying to make an extension cable for my telescope hand control.

I have had good results with the 25' length  but it is to short . So I made another one 50' in length but it give me connection error codes. The cable is correct as it worked for a while .I am using an rj12 6pin connector with cat5 cable(24awg). The power supply is 12V DC with 2.5 amps running on house AC.

The question is: If I put a different power supply on that is 12v DC using 5.0 amps will the increase in amperage effect the DC current flow?



Thanks,

Don
      

I bought a LED fixture that fits in a 4inch can

http://indoors.pricegrabber.com/show...s/m/928501559/



The thing iswhen I pushed the fixture in I niked the black wire from the can's socket. What should I do replace the socket or should I just take the can's socket out and also the LED socket out and use marettes?   The thing is I don't have much cable from the box the romex is about 6 inches long and was cut to lenght!!!
      

QUESTION:  can I run (2) 14-2 romex wires in (1) 3/4 BX Armored cable?



SETUP: I am finishing my basement and a few main floor circuits are intermingled with the basement lights and outlets.  In finishing the basement, all basement electrical will be on its own circuit. Therefore, I need to rewire some main floor items.



For instance, the main floor living room outlets go through the den area below in the basement. The 3/4 BX cable goes through the ceiling to the outlets.



PLAN:  I plan to cut the armored cable shortly after it comes out of the ceiling (main floor floor) and just connect the first floor outlets in a series using the proper bushing and BX cable ends. I will strap the BX cable ends down and the romex as soon as it comes out.



The electrical inspector already gave me thumbs up on doing this for the electric oven and cooktop (bigger wires of course).



I searched and couldn't find anything to this specific question.



Any input?



B