Crooked Work Box Wont Sit Flush
Have a 2 gang box with two outlets in it. The side opposite the stud protrudes from the wall 1/4 or so. It pushes in too so when you plug something in it is spongy. Any fix other than replacing it?
Similar Tutorials
How to Lay Sod - The Right Way!
- Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
- This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
- If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ... Similar Topics From Forums
i am rewiring a bedroom. the wall with the window is 10'ish. on the right side of the window = between window and corner, will be an outlet.
the left side of the window. there is a closet door, on the left wall, that opens to be flush with the window wall. so no furniture can be put there. should i put an outlet there anyway ?
Hello All
So I have a beginners question. I am remodeling my basement. The existing electrical is fine, but all of the boxes were hung from the old wood paneling (not mounted to the studs) using some sort of hooks/pins. I had a friends dad (who is a master plumber) come in, and he said those pins are fine for occasional use, but should not have been used everywhere. Should I mount the boxes to the studs? If so, should the boxes be flush with the studs, or should they be 5/8 extended out, so they will be flush with the Sheetrock? My gut says 5/8 out, but watching youtube clips I only hear flush with the studs. Any feedback would be greatly appreciated. Thanks. -K
hi guys,
Im a 1st year apprentice sparks so pretty inexperienced! i have a job on during the week to wire a bathroom extractor fan in for my friend. He wants it to come on separately from the bathroom light. Theres a 2 gang switch outside the bathroom, one for landing lights other for bathroom. So im thinking of replacing this with a 3 gang switch for the fan. Im gonna take permanent feed from one of the two other switches ie(bathroom or landing) to the fan switch 'common' to power it, then also take a permanent feed for the fan from the 'common' side of this new switch as its a timer fan. Then switch feed from L1 on new switch to fan. And finally neutral from bathroom light fitting to fan. I know that these 3 cables going to fan have to be isolated at another switch before going to fan! Am I on the right track. Thanks in advance.
I have 2 light switches in my entry and need to add a 3rd. So…I removed the old 2-space metal box and will be replacing it with a 3-gang old-work box.
The issue I’m anticipating having is: The old knob & tube wires coming in aren't very long. As the locations of the openings for the wires in the 3-gang box is a bit different than the old box, I’m worried that the wires now won’t be long enough to now reach the light switches. So, my questions are... If I need to add 6” or so to some of these wires, is it okay to just splice a new piece of 14-gauge wire onto them?? I simply didn't know if you're allowed to do this. If so, is this just a matter of using a plastic twist cap to connect them…with everything being done inside the new box? Thanks so much for your advice.
I want to set up a hobby woodworking shop in my garage. I was going to run from the panel maybe four or five 12/2's to accommodate lighting, power tools, dust collection, etc. or should I put a subpanel 60 to 100 amp? The main panel is on an outside wall on one side of the house and the garage is on the opposite side of the house. The distance from the panel to the entry into the garage is about 50 ft. I would be pulling wire- a straight run- through a ceiling chase that runs the length of the house. No basement.
what the fudge sticks man?
I am not a DIY'er or a handy man but I gave it a shot.. I replaced an old a$$ receptacle with a brand new one and I wired it EXACTLY the same as the old one.. I know this because I did it WIRE BY WIRE!! i.e. I took 1 wire off the old receptacle and installed it on the new one.. wire by wire.. Power works and all that.. BUT NOW the ONLY light switch in the room does not control the bottom receptacle anymore? what gives? i don't get it.. what changed? Previously the light switch gave power to this outlets bottom plug, so I had the lamp plugged into it and turned it on/off with the light switch.. but that doesn't work? I even triple checked my work and still not seeing whats up? any ideas? oNe. p.s. HOW do you release the wires on these new fangled outlets? It says push spring in slot to release but I am not seeing it? any ideas?
Hi, I have a problem where if I turn off my light switch on one side of the room, it turns off anything plugged into the electrical outlet on the other side of the room. For some reason, they originally wired that outlet on the same circuit as the light switch. I would like to wire the outlet so that it does not switch off whenever you switch off the light on the opposite wall.
How do I go about doing that? Thanks. (p.s. There are just the basic three wires in the electrical outlet; black/white/bare copper ground).
My existing service entrance consists of an external Meter can mounted on the outside of the garage wall directly behind a SD Main Breaker Panel (MBP) with a 150 amp main breaker. In order to support upgrades, I am installing a second MBP (200 amp) inside the garage in the wall cavity right next to the existing panel.
Local code requires that the upgraded Meter can be purchased from the City Utility. I have already confirmed with the local inspector that either 4/0 Al or 2/0 Cu SE cable are acceptable for both the existing and new MBP. My question is what is the code requirement for getting the 3 SE cables run from the dual lugs to the new panel? Can those conductors run into the same wall cavity where the existing panel is installed? If so, I'm certain they can't go through the same conduit nipple that connects the back of the meter can to the existing MBP. Can they route in behind/above/below the existing panel and through a hole in the wall stud to gain access to the adjacent stud bay to get to the new panel? If not, do they need to be routed out of the meter can on the external wall in conduit over to the next stud bay and then enter the wall there to gain access to the new panel? If external conduit is required I would expect it must be metallic as opposed to PVC. Best Regards, Ted
Going through a crazy heat wave here in SoCal, and one of my tenants called to tell me that the electricity isn't on in some of his rooms. He turned on his portable AC unit that he has been using all summer and something may have happened.
Downstairs:The dining room light switch, downstairs light switch do not work. All outlets around them do work though, which is odd cause I would have thought they'd be on the same circuit. Upstairs: The side bathroom light switch does not work, but outlets all work. In the master bedroom (where the AC unit is located), the master bathroom light switch does not work, nor does the master bedroom light switch. All of the outlets do not work either. I used my outlet tester and it gave me the hot/ground reversed lights. I think this means that the white/black wires are reversed on the outlets (has not changed recently). I went over, checked all of the breakers. Switched them to off, then back on, did not fix the issue. All breakers stay in the on position without tripping, so no shorts? Checked all GFCI's, hit test, then reset, did not solve the problem. We unplugged everything from all outlets, and retried, but it didn't work. I checked continuity between the main power lines, and the output of the circuit breakers, and all were fine. I did NOT check the voltages though, and will do so in the morning when I stop by again. Is there anything else I should check?
I am putting a theater area in my basement, but my electrical panels are also in the same room. To keep the room symmetrical, it would look best to install the new panel two stud bays over and put the sconce in between - then it would match with the sconce on the other side. I can't put the sconce on the other side further back because of a doorway. I plan to paint the panels the same color as the walls so they blend a little better.
Anyhow, I attached a picture of the proposed layout. The sconce sticks about 5 inches out from the wall. Will the inspector approve such a setup? I should still be able to access the panels without an issue, but don't want to do something against code, or stupid in some way. Thanks! |