Dryer

Can a gas dryer share the outlet with a washer in a utility room?



What if they are small under counter units in the kitchen?
      

Ya know when your g/f or wife says, 'Don't you DARE talk down to me?'... well, I AIN'T your g/f or wife but what i IS is so DYI challenged that anything but the most basic explanation will cause my brain to short circuit.



To prove how DYI-tarded I am, I bought a used staking washer/dryer because it was what I could afford.. but now I can't plug it in. The plug is a large crows-foot deal but my outlets are standard USA deals.



I know it can't be as simple as changing the cord to a standard 3-prong.





KENMORE STACKING WASHER/DRYER  MODEL NO:  417.90802992

WASHER 120/240V

DRYER   240V

APPROX 4 YEARS OLD

EXCELLENT CONDITION



... the part number on the plug is E11808



Any suggestions (unless i starts with 'shove it up your') are appreciated.



Thank you - Mick
      

I'm new to this site.  But would appreciate some troubleshooting.  I just renovated my kitchen, gutted and all, finished in the Fall.  I did not replace wiring to the dryer, nor tamper with it, to my knowledge.  We did have an electrician add a small fuse panel.  We did not add more appliances then before, added some lights, but mostly used the room to separate things out.  Had a mentor do the wiring, many years of experience, very tidy and careful work, though not electrician by trade.  We have a standard 200 amp box as far as i know.  The house is 100 years old, but the wiring isn't.



In October my mother in law heard a very loud bang.  The electric dryer had been running.  She smelled smoke.  At the dryer receptacle was molten plastic sprayed onto the wall, caused by overheating at that point, due to I don't know what.  I thought maybe I had knocked something loose in the receptacle when i was drywalling around it.  I can't remember now if the breaker had tripped.  The receptacle and plug were toast. 



I replaced the receptacle, I replaced the dryer cord, not the breaker.   The dryer worked fine until february, when it stopped heating.  I found a bad thermal fuse and replaced it, the very common two pronged white one. 



The dryer worked fine until early April when it stopped heating again.  I checked all the fuses/thermostats on the back and the heating element, as I had done the first time.  Nothing was bad.  I checked the voltage coming out of the wall, as I had done the first time, only this time I did it correctly and got a reading that told me to check the breaker in the panel, which had not thrown.  When I checked the voltage between the Nuetral Bus and the two terminals on the Dryer's 30 amp breaker I only got a good reading on one of them, telling me that the breaker was bad.  While at the box, i noticed that to the main breaker, from where the conduit comes into the box from outside, the nuetral wires are bare all the way up, no insulation, and at the terminal of the main breaker they appear to have all melted together, even a couple small pieces have melted off of the "bundle." 



Switched the range 50 amp breaker with the dryer, dryer worked fine, nothing was back fed either.  Bought a new 30 amp breaker for the dryer and installed it on Saturday.  Also on Saturday we were given a dryer, about 4 years old, same as ours, so i hooked it up and saved ours for a spare, which I deemed still good since it seemed the breaker was the issue.  New Dryer worked fine from saturday until today.  Now it won't turn on, though it didn't cut out mid load yesterday either.  The breaker did not trip.  I repeat, no tripped breaker.  I just checked the voltage at the wall and it seems to have that same problem where one side of the receptacle gets a reading of 120, and the other a reading of about 5.  The problem must be bigger than the breaker.  I am not an electrician, I am a welder.  I have gone as far as I could on my own.  Thank you.
      

I have a 220v Microwave, and a 220v dryer, that came with a four prong plug cords attached (they were used in newer homes).



The current outlets are three prong outlets and there is absolutely no way to run new wiring.





Just need to change the cords on the microwave and dryer to the old style three prong ones?









Opinions?
      

I am installing central air conditioner in our 80 year old house. Debating between one high velocity system or two conventional systems.



We have 100 amp service with an electric dryer, stove and oven. Water and heat is gas.



The HVAC contractor told me that he spoke with the electrician who assured him that we would not need to upgrade service but add in a sub-panel.



Any thoughts?



What are the risks of staying with current electrical service and adding A/C? What are the risks of upgrading to 200 amp with such old wiring? Is one high velocity system better than two conventional systems?



Note I am cross posting based on another question I had in the HVAC forum.



Thank you in advance for all your help.
      

OK, I'm an electrical dummy ...



I have finished basement w/a bathroom. We have an ejector pump off the bathroom that has been plugged into an outlet w/gfi since I've owned the house (10 years). There is also a booster fan for my electric dryer plugged into the outlet (has been the same for 10 years).  The only thing that has ever tripped up that outlet is using a hair buzzer in another outlet within the bathroom (but once you hit the reset its fine).

   

  This morning I realize the ejector pump was not sucking down the water from the drains. I looked at the outlet and realized it needed to be reset. When I reset it, the pump would run for a few seconds and the outlet would trip up again. Tried this a few times. Thought maybe it was an issue w/the outlet altogether. Neighbor suggested maybe it was an issue with the pump. Went thru various scenarios and bottom line is when I plug the pump into other outlets it works totally fine and once I do that and reset the outlet it was on, the booster fan works fine and the outlet does not trip. So, basically this outlet is tripping when the pump is on it but the pump is not tripping other outlets and the outlet works fine as long as the pump is not on it.

   

  What could be causing this? Why would an outlet that housed the two things on it all of a sudden continue to trip when the pump is on it but the pump is fine on its own in another outlet and the outlet is fine on its own w/o the pump?
      

Hello All,



I'm about to "re-locate" some existing breakers and wires into a subpanel and have a few questions.



1) My existing hot water heater is wired with 2 conductor w/ground wiring (30 amp, #10 wire). Is this still Code compliant or do you have to have 3 conductor now as with dryers?



My existing dryer also has 2 conductor w/ground wiring (installed in 1999).



If I relocated it or the hot water wires/breakers to my new subpanel will they require me to upgrade to current code (3 conductor, if applicable)? The subpanel will attach to the Main Load Center which is where those breakers/wires are currently attached.



Main question is will I be grandfathered with existing wiring in only relocating the breakers/wires to subpanel?  I'm not relocating the appliances or recepticles themselves.



2) I have 3 conductor w/ground wires for my cook top. It only requires 2 conducter w/ground however. They wired the ground/neutrals together but has flexible metal conduit running to the cook top itself. Should I remove the ground and bond it to the metal conduit?



Thanks, Ralph
      

On my second floor with a High / Low switch and a timer hooked up to it.  The fan works fine on high and the timer works - but if I try to put it on low it stalls out.  I can hear it try to work - it sounds kind of like trying to get a car to turn over.  It starts up, spins for a second and stops and repeats that cycle until I turn it off or set it to high.  The fan was installed when I bought the house so I have no idea how old it is or its brand / model.



Does anyone know what might be causing the problems on low, is it still OK to run it on high, even with the issues on low and is this something that can be fixed easily or does it require special services - electrician or otherwise?
      

Tearing out a wall cabinet uncovered a hole in the wall which I think I can install an outlet on.  The problem is that the ground wires are to short to pull out far enough to attach to the outlet.



However, the box in the wall is metal, so there should still be an path to the ground from the outlet right?  Or is there something special about the green screw on the outlet which makes that the only safe spot to attach the ground to?



box I uncovered:

https://lh3.googleusercontent.com/-v...s538/photo.jpg



fuzzy picture of the inside of the box showing the ground being attached to metal box:

https://lh6.googleusercontent.com/-B...303_154810.jpg



The outlet I want to install... (although I dont know how to pick the right outlet based on the limited info on the wiring I have, so any help with that would also be appreciated):

http://www.homedepot.com/Electrical-...&storeId=10051
      

I live in a 5 unit single story condo in Florida. I want to run 100ft of 12 /2 cable in a coomon low attic. This is a flat roof with roughly 3 ft high roof truss support. This will end as outlet for a golf cart.



Almost impossible to drag this wire along, How can i get this 100ft to the outlet? Yes it will cross over the other 4 units.



Thanks