Home Electrical / Car Stereo Question

I know nothing about car stereos, but I had a crazy thought the other day and figured someone here on this board would know home electrical stuff and also car stereo (electrical) stuff.... so here goes....



How difficult would it be to "rig up" a car stereo (or, actually, an in-dash video player/receiver) in a house, hardwired in?



I assume (admittedly, without researching) that the foremost issue is that car power is DC, so the first problem would be getting a transformer to take 110VAC to whatever the stereo required in DC, right?



As far as speakers - are car speakers and home speakers essentially the same, as far as the signal sent to them from the receiver/amp/radio? Or are they a different capacity (resistance ohms or something)? Could you use home speakers (say, small in-ceiling type speakers, like you typically see sold for home theater surround usage) with a car stereo?



Finally, do these systems typically have standard audio and video inputs in the rear (component, composite, S-video, headphone-jack type plug)? I know they typically have an "aux" input on the front (for video game systems, iPods, MP3 players, and whatnot) but do they have connections on the back where it would be out of view when permanently connected (for connection from the satellite box)?



I had this crazy idea that I would love to install one of those car stereos with the slide-out, pop-up TV screen into my bathroom, and have the sound wired to ceiling speakers. If I built a cabinet with a mounting frame that would hold it in place, could this work? I am not looking for some high-end sound system that will blow me away and rock the house, nor do I care about a beautiful HD picture on the TV... I just want to have a small TV and a radio/audio receiver at the vanity area that I could hear with the shower running or whatever, and car systems like this are way less expensive than buying a small LCD TV and a stereo receiver (plus I can't find a receiver small enough). Plus, you would get the added benefit of the TV "disappearing" when not in use. 



Obviously, this would take some rigging - transformers and all - but can anyone clue me in on the feasibility?
      


Similar Tutorials

How to Lay Sod - The Right Way!
   - Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
   - This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
   - If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ...


Similar Topics From Forums

I'm building a whole house everything system. It is a sixteen zone system with full AV distribution, 9 security cameras, about 70 speakers, ten 9.1 surround sound amplifiers, 6 PCs, KVMs, loads of networking gear, two dss, bluray, roku, squeezebox, NVR server, NVR viewer, etc. There are air conditioners in the Liebert MCR racks. The headend contains three 42U racks. Two of the racks are for AV equipment and the third rack is for the PC equipment.



Here is a detailed list of all the equipment and their electrical needs:



http://dl.dropbox.com/u/70589/MillerPlan.xls



You will see two tabs on the spreadsheet: Equipment and Cabinets. These contain very detailed information on all the devices going into the three racks. You will see that I specified 14 electrical circuits.



I have already purchased all the equipment except for the "APC UPS 280 watts" and "Furman power conditioners". If anybody experienced with residential systems with requirements like this could give me feedback on the electrical requirements and my proposed design it would be great, all feedback is welcome!
      
I am renovating my modest home's living room, but, since the walls and ceiling are basically stripped bare, I would like to consider "toys and luxuries" which would need to be wired in upfront here, such as ipad syncing controls for stereo or lighting, decent built-in speaker systems, etc.  What kinds of devices are contemporary homes incorporating nowadays?  I am not super-nerdy, but a couple "gee whiz" devices might be fun to have!   Suggestions?   Thanks in advance.
      
Came across this gem tonight:



  I know most people have  become or are aware of the importance of the use of audio grade AC wall  outlets. What most people do not know is the importance of using the  right AC wall outlet plate also. Most AC wall oulet plates are metal or  plastic. Replace all of your AC wall outlet plates in your audio and  your home theater systems with wooden AC wall outlet plates.



If you purchase finished wooden plates, lightly sand them with "rough"  sandpaper until the sound is to your liking -- the sound will go from  "thick" to "more harmonically accurate" the more you sand it. Sand  lightly at first, take a listen and if the sound is too "thick" to your  liking, sand some more until you get it to your liking.



The best thing is to start out with unfinished wooden plates, sand them  lightly with medium sandpaper and then apply a very thin, light coat of  "clear coat". Allow the plate to dry and cure for 24 hours and repeat  this procedure.



If done correctly, you will notice that your video picture will sharpen,  the colors will blossom and the sound will be more harmonically  accurate with better resolution and refinement.



  http://archive.avsforum.com/avs-vb/showthread.php?threadid=36999&highlight=sanding
      
Hi all, I need a little help here, and wanted to see if anyone on the forum has installed a volume control switch for speakers?



Model NXG  NX-VMS1000



First question: What type of electrical box would work for this switch? Old work. Needs to be deep enough.



Second question : I have 3 pairs of speakers connecting to this, 3 lefts speakers and 3 right speakers. I think I will have to connect all left pairs and all right pairs since the switch only has a left and right input and a left and right output. All suggestions are welcomed.



Thanks
      
Help!  We decided to raise the ceiling in our kitchen for some new taller cabinets. We have 30" cabinets with a 7' drop ceiling. By taking out the drop ceiling we can go to an 8' ceiling with 36" cabinets.  We just had the ceiling taken out and now I see I got a problem!



This is a 2 story home, the wall in question is a load bearing wall (runs through the center of the house) The main breaker panel is in this wall (the panel opening is in the adjacent family room)



As you can see in the photos I cannot extend the wall up because all of the home wiring is in the way!  I expected I might have to run longer wires but not this. 



Some ideas we've thought about...

notch the double 2x4s (not sure how much I need to notch or allowed to)



build a cove (box) and leave the wires like they are (might be an eyesore in our new kitchen)



put up a large crown moulding along the entire wall (would be the only crown moulding in the house)



extend the ceiling up 6-7" instead of 12" (should leave enough room for wire to stay)



I'm leaning to the notching option if I can find a way to reinforce that section.



Any ideas?



thanks!
      
Hidy!

Hoping someone can guide me in the right direction. I have essentially no experience with electrical anything unless its a computer, and I am remodeling my Mother's guest room. We picked a pendant light to replace the old flushmount lighting. I've got the old one removed (and yes I have the power off in the room ), and I cannot figure out how to do this based on the instructions given (or on any video I have watched).



There are two copper "wires" coming down from the ceiling. They are both wrapped in black insulation, and they form like a little hoop/circle on the end. The fixture has a copper wire, not insulated, and like a double copper wire insulated with brownish black coating. Sorry...I don't know technical terms here, but I would be happy to post pics.



I just need help installing this thing. I've done flooring and plumbing and everything else you can imagine a chcik might figure out how to do, but I am stumped here. Please help me do this! It doesn't seem like it should be this difficult!
      
I had a tv plugged into an outlet in my garage. The tv crapped out due to bad wiring {I think}. The reason I say bad wiring is because when I have a radio plugged in I can hear static through the speakers due to the wiring. Garage was built in the 70's. What do I look for when checking the wiring from the house to the garage and then all the garage wiring itself?
      
We are revamping our patio area a bit which is off of our sun room.  I was wondering if anyone has ever heard of installing in-ceiling speakers in soffits?  If so, could you provide some tips in doing so? Thanks!
      
I've had an on-off problems with two of my ceiling fans (different makers, one hunter and one minka). Wired differently too, the minka one is controlled by a wall remote control, and the hunter one by two wired wall switches).



Every now and then, for no reason, the fan will stop working. It may stop working for a day, a week, whatever.. then start working again for a month or even a year. When this happens, the light kit on both fans still works (on the minka, the light kit and fan are on the same line, separated in the fan by the remote control receiver. On the hunter, it's two different wires going into the fan.).



It stumps me.. I'll just turn the fan on one day, it will spin a little bit, then stop. Nothing gets it to work. I can hear a small hum in its motor, like it's getting power, but it won't spin. Then a week later I may accidentally turn it on again and it will run. Two and three years ago I had repeated on/off problems with both fans. Last year, both worked perfectly the entire year. This year one of them has started acting up again.



Any hints would be appreciated.
      
Here's a somewhat unusual situation. I have a digital video recorder and a small monitor, both of which I'd like to power off of a car's cigarette lighter simultaneously.



So basically I want to eliminate the standard outlet plugs (and the power supply on the monitor's cord, like a laptop's power supply), and solder everything into one cigarette plug.



I already know how to solder +/- leads to the cigarette lighter, then split into two, but I'm not sure what needs to be wired between the lighter plug and the components so that the proper voltage and amperage gets to each component.



Any help filling in the gap in my diagram? Thanks!