Outlet Behind Door ?
i am rewiring a bedroom. the wall with the window is 10'ish. on the right side of the window = between window and corner, will be an outlet.
the left side of the window. there is a closet door, on the left wall, that opens to be flush with the window wall. so no furniture can be put there. should i put an outlet there anyway ? Similar Tutorials
How to Lay Sod - The Right Way!
- Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
- This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
- If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ... Similar Topics From Forums
What size wire is needed to run 100' from the main breaker panel at the house to a portable building? The load center at the protable building will run an 8000 BTU 110V window AC, two single bulb light fixtures and one 110V wall eletrical outlet.
Thanks for your help.
Hi everyone, this is my first post. Hope it works out!
I have a new detached two car garage with two 115v 15A circuits in it. I want to put in a 12000 BTU window air conditioner. One circuit runs 10 fluoresent bulbs in the garage and a few in the house but also runs a few outlets in the house that see occasional use by a 12A vacuum cleaner. The other is solely used for the door opener and outlets in the garage where I often use a 12 amp skill saw. Both circuits are aqccessible, which one should I choose? Puttster
We are just beginning to start with our kitchen remodel. Today, I mapped out all the circuits and this is what I found.
Circuit # 7 - 20 amp circuit to 1 back splash outlet then to 3 kitchen wall outlets, then to a closet outlet and closet ceiling light and then to a side porch light! Circuit # 8 - 20 amp to Dishwasher and Disposal Circuit # 9 - 20 amp circuit to microwave and kitchen ceiling lights. 2 patio recessed lights and dining room ceiling light. Circuit # 12 - 20 amp circuit to another back splash outlet then to 2 dining room wall outlets. Circuit # 14 - 20 amp to Refrigerator only Circuit # 18 - 15 amp to GFCI outlet in garage then that feeds 3 outlets for 3 bathroom outlets and 1 outside patio outlet. I going to have to add 1 more back splash outlet due to increase in counter space. I'll put the microwave on a dedicated circuit. So I need 2 additional breakers but I only have 1 blank spot in the breaker panel. I guess I can add one of those slim tandem breakers. So my question, is it ok to have additional wall outlets on the same circuit as a back splash outlet? If it's ok I'll lighten up circuit # 7 by putting some of those wall outlets on the additional back splash outlet. Oh, I have 2 20 amp circuits I did not get identified yet! I'll get to those tomorrow. thanks!
Hi, I have a problem where if I turn off my light switch on one side of the room, it turns off anything plugged into the electrical outlet on the other side of the room. For some reason, they originally wired that outlet on the same circuit as the light switch. I would like to wire the outlet so that it does not switch off whenever you switch off the light on the opposite wall.
How do I go about doing that? Thanks. (p.s. There are just the basic three wires in the electrical outlet; black/white/bare copper ground).
I have 3 bedrooms on 15 amp circuits, 14 gauge wire. Original wiring is one bedroom is on one circuit and the other 2 bedrooms on another circuit. The wall switches in each switched the top half of an outlet in each room. I converted the wire at the wall switch to a 110V feed from the outlet and ran 14/3 from the switch to the ceiling for a ceiling fan. I replaced the outlets since the jumper was cut to isolate the 2 plug ins for switching. Is this whole scenario code compliant?
Hey guys,
I am trying to convert several 2 prong to 3 prong outlets throughout my house that was built in 1959. I have attached 2 photographs of the outlet, one from the right, and one from the left. You will see the right side of the outlet has a RED and a BLACK wire attached to it. The left side has a WHITE wire. I took the Menards employees advice that the black wire was most likely the ground, hooked it up, and blew a fuse (time delay fuses....). When I tried screwing in another fuse, it blew right away. This happened about 4 times and I got frustrated and decided to try this forum. Any ideas as to which cable would be the ground, if any?? I'm pretty new to all of this. Any advice? Thanks!
I only have one outlet in my living room and I need another one for sure. What are some ways I can do this? There is not another outlet on the other side of the wall, we had a electrician come add a light with switch and he said something about closing off a line behind the switch box. Is it possible to re-open that line? We also have a attic which I was told at homedepot is easy to do if you have another outlet in the next room you don't use. Any help is greatly appreciated!!
Hello everyone,
I am trying to replace a 40-year old garage door opener that stopped working, and the motor reads "250v"-- are 250 volt openers standard? does the 250v mean something completely different? or will I have to re-wire it to a standard 110v outlet type to put in a new opener? The original cover has most likely been lost to time; the brand was Overhead Door company. I haven't purchased any new openers yet, making sure I know what I am getting into first :-) The door is not especially large --9'x7' not sure of their weight; if it matters, the door will likely be replaced shortly as well. Thanks for any and all help!
So I have an outlet in my living room which has recently stopped working. I checked it with the voltmeter and it shows 90V output instead of the 120V AC which it should be normally. The fuse that this is on is fine. I also disconnected the plug behind the covers and tested at the wires themselves and it's still 90V. So the problem is not at the outlet side but either in the wall or somewhere else?
Is there a way to debug this or is this even a more common problem? Thanks!
Tearing out a wall cabinet uncovered a hole in the wall which I think I can install an outlet on. The problem is that the ground wires are to short to pull out far enough to attach to the outlet.
However, the box in the wall is metal, so there should still be an path to the ground from the outlet right? Or is there something special about the green screw on the outlet which makes that the only safe spot to attach the ground to? box I uncovered: https://lh3.googleusercontent.com/-v...s538/photo.jpg fuzzy picture of the inside of the box showing the ground being attached to metal box: https://lh6.googleusercontent.com/-B...303_154810.jpg The outlet I want to install... (although I dont know how to pick the right outlet based on the limited info on the wiring I have, so any help with that would also be appreciated): http://www.homedepot.com/Electrical-...&storeId=10051 |