Lamp Post
I have a lamp post outside that I am going to replace this spring with a new one... right now they just have 14-2 romex ran underground to it... not in a conduit or anything... should I replace this with UF cable? or is NM cable still the way to do something simple like this? Also should I use conduit?
Similar Tutorials
How to Lay Sod - The Right Way!
- Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
- This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
- If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ... Similar Topics From Forums
So I recently bought a home. There was an old rusted and rotted lamp post out front. This past weekend it blew over in the wind. Not kidding. I turned off the circuit on our breaker box, i unscrewed the caps connecting the main wire to the lamp head. I removed the poll lamp head, can I just recap the single wires and roll the wire back into the ground? Will just capping the wires be safe?
I want to run Romex from a j-box, that is in the ceiling of my basement, to the main panel. I know that I can run Romex from the box along the face of the joist (not the bottom), but what are my options once the Romex gets to the wall? The joist I am using, conveniently enough, meets the wall ideally for where the panel is. However, I've read that I need to run the Romex through EMT, or some form of conduit.
If you look at the picture I've attached, the panel is mounted on a piece of plywood that extends out underneath the joist. Can I just staple the Romex to the plywood and then run it into the panel without using any conduit? The cast iron pipe makes using any conduit quite a problem. The cable you see is MC Lite, but I want to replace it with Romex. There are going to be up to 9 more lines coming into the panel this very way.
I am running power about 180 feet to power a 60A subpanel in an outbuilding. I am expecting to use 2-2-2-4 AL. The run is underground for about 150', and the balance through crawlspace and basement to the panel. My question is: can I use a sheathed cable such as SEU in the conduit so I can simply continue (unconduited) under the house, or do I have to run URD in the conduit to a juction box and change to a sheathed cable to run under the building? Or can i run URD in the conduit under the house to the panel (this would be less preferred). Thanks
Just curious which is the prefered way to get the electrical cable through the conduit, and why?
I see some pull a rope through as they glue the conduit and pull the wire when done. Others feed the cable through each individual piece of conduit as they go along. Thanks in advance for your answers.
I have an older home and i wanted to add a new 15 amp breaker for a circuit for the outlets for my upstairs. I noticed that the existing old black romex runs from the circuit breaker in electrical conduit in my walls. There is no way i can get more romex through that conduit. Can i add the romex outside the electrical conduit? i am not really sure why they ran through the conduit to begin with.
I have an outdoor light fixture that I am trying to replace. The house was built ten years ago.
When I removed the original lamp, I noticed one of the two leads was wired to the ground, and one was wired to the black wire, which is hot per my current sensor. There are three wires in the box - black, ground (bare copper), and white or neutral, all from a single romex cable. Unfortunately, I do not recall where the white was when I removed the original. I wired the new lamp per the instructions, something I have done many times before - black to black, white to white, and bare copper ground to ground. Nothing. The lamp and bulbs are brand new, and I have tried four separate bulbs. I checked the black and neutral with my current sensor and with the switch on and the lamp installed this way, both show as hot. With the lamp not installed, the switch on, and the wires disconnected only the black shows as hot. The switch is single pole, and appears to be wired correctly with a black to each screw on one side and a copper ground on the other. Assuming the new fixture was bad, I reinstalled the old fixture correctly - black to black, white to white, and bare copper ground to ground. Still nothing. No light, and I confirmed the bulb is good by putting it in another lamp. The only way to get it to light is to connect the neutral in the lamp to the bare copper ground. I capped the wires, turned the circuit back on, and identified all the outlets, switches and fixtures on the same circuit. I opened every one of them up (four lights and eight outlets) and found three (one switch and two fixtures in another room) where multiple commons connect. All were properly connected. My outlet tester shows all outlets as "correct". I found no instances of grounds connected to commons or vice-versa. Any ideas? Is it proper to wire this thing the way I found it? Thanks for any and all advice!
Hi all!
I'm trying to install an outdoor box for my low voltage lighting controller unit. I have an electrical junction box that's split from indoors and leads to a post lamp. I'm wondering how I split this junction box off to a simple 110 receptical for my outdoor lighting controller. I've attached a picture just in case I didn't explain well. Thank everyone for the help!!!
I have a 50 foot hdmi cable that is hooked to my TV, run through my wall to my basement then over and upto a closet where the cable is hooked to my surround sound. Unfortunately my basement ceiling is finished in drywall and there is no access to replace the cord. To make a long story short a cable TV provider came to my house to change out a box and broke the prongs on the hdmi cable. My question is, can HDMI ends be spliced or replaced somehow without replacing the whole cable.
I have an older house I which I need to replace/update some romex wiring. I was planning on turning of the power to the circuit, remove the devices from the wall box and then remove the box. I was hoping to use the old wire to pull the new wire. My problem is how to remove the old wire from the cable staple so it will be lose to use for pulling. Any suggestions?
Is it permissible to run a single bare wire from an ungrounded receptacle to the panel if the bare wire is not part of the Romex cable?
May a bare wire be ran to a j-box that has a ground while being outside the Romex jacket? I don't want to run a new cable, as I have plenty more #14/#12 bares than I do full cable. Thanks |