Dimmer Switch/light Switch

Can you install 6 recessed light off of one circuit by starting at a switch that is designed to turn an outlet on and off for a lamp that sits on a table.  i've determined all of the outlets in one room are on the same circuit.  The max wattage that will be used in that room if all recessed lights and TV etc are on would be approx. 1,500.  the electrical wire in place is 14 g.
      

Hey guys and gals,



got a very odd dilemma, in my dining room there is a chandelier lamp that is controlled through a dimmer switch(even though it is not a dimmer). There is also a closet with a light switch as well.



The odd circumstance i am having is when the closet light is on(via its own switch), and you turn on the dinning room light, the closet light goes out. Then if you turn the dining room light off,the closet light turns back on.



The closest light switch has zero effect on the dining room light, the dining room light seems to have control over the closet light and dining room light.



Any ideas on a fix. I was thing just replacing the dimmer(once again does not actually dim) with a single pole interrupter. I just dont want to burn my house down
      

I've installed two dimmer switches in the bar area of my basement. It's the dial type, where you can push the dial in to turn the light on or off, or turn the dial to dim the light. One dimmer operates the recessed lights in the ceiling, and the other dimmer switch works a pendant light that I have over my bar. The dimmer for the recessed lights works totally fine. They turn on, off and dim. The pendant lights, on the other hand, only turn on and off. They for some reason will not dim. I checked the voltage on the pendants to see if maybe it was an issue of the switch being a high voltage dimmer operating low voltage pendants, and the pendants are 120V with 75 max wattage. I'm at a stand still. I have no idea what I'm doing wrong. Do any of you have suggestions? I took a couple pictures, not sure what good they'll do. The best I can do for a camera is my iPhone, so they're not the best quality.








      

I am working on fixing an issue with the wiring in one of the bedrooms in my older mountain home. Though I was not present for the cause of the problem, here is what was told to me by the tennant.  he claimed that he went to turn on the light in the closet, (a 3 lamp track bar light, wired to a switch) he heard a loud pop from the light in the closet and lost power to to the room. The room has 6 recessed ceiling lights on 2 separate switches, presently only half of the lights work.There are no breakers tripped, no obvious shorts at outlets. I have opened the drywall following the wires around hoping to find a short but I have found nothing. I decided to try something, and I bridged the working switch to a dead outlet and everything turned on. I am waiting til the daytime to follow the wires outside to the breaker box, but so far no breaks or anything.. curious if anyone has any pointers.. could the pop he heard from the track lighting have killed a breaker? its about the only thing left.
      

I replaced a ceiling light with a fan/light with a remote. everthing works. their is one light switch and one dimmer switch. The dimmer switch has a red wire and a black wire connected to the black wires coming out of the dimmer switch, plus a green wire hooked to the metal portion of the dimmer. My question is: Do I have to remove the dimmer switch, if so, can I disconnect the red and black and hook them together? If I have to replace the dimmer with a regular switch, what kind of switch do I get?

Thank you
      

i have just installed 4 cans controlled by a dimmer switch using 14/2 wire and plan to hook into a 15A circuit. The easiest wire for me to hook into this circuit is on the load side of a receptacle that goes to another receptacle. can I cut the wire that goes between receptacles and split the hot wire so it goes to the new recessed cans ( same for the white wire) and then on to the receptacle as previous?

Thanks

Tom
      

Okay, I am fairly new to wiring but its not the wiring I am wondering about.  It is running the wires.  I have 2 rooms in my house, 2 story and an attic, on the main floor that doesn't have any overhead lighting, only can use floor or table lamps right now.  The ceilings are about 10 feet tall.  There are outlets in the room so I do have power I can tap into for the lighting, but how do I go about running the wires up into the ceiling?  I do know I have to cut the hole for the lighting but will i have to put cut flaps in the drywall where ever there is a brace to drill holes to run the wires.  I am going to go from the middle of the ceiling straight back to the wall and then down to the switch that I will put in and then down to the outlet to tap into for the power.  I am just trying to do this the easiest way to minimize any drywall repair that will be needed.  Any help or suggestions from anyone is greatly appreciated and if you have questions please ask and I willl try to answer them.
      

I have a 2 story house, I just had the drop ceiling in the kitchen removed and it will be raised up 12".

Right above the kitchen is the master bedroom. When the new drywall goes up that space becomes inaccessible.



I assume I cannot install "new construction" type recessed lights in the kitchen?
      

hi everyone.



i am installing 4" recessed lighting throughout my main floor.  my house was built in the 40's and the previous owner installed drywall over the existing lath and plaster ceiling.  so I've cut a trench down the center of my room to drill floor joists to run wiring and cut my holes for the new lights.

the lights are fire rated and do not require insulated cans for a traditional installation in a drywall ceiling.



question i have is with the additional 1/2 to 3/4" of lath and plaster above the drywall, should these lights now have insulated cans or should i be fine with the cans I've got?  there is no insulation in ceiling.



any suggested would be appreciated.



thanks

d
      

Having a brain freeze, if someone could take a moment to explain this to me, it would be greatly appriciated. I am wiring four recessed lights in a bedroom, off one switch. I am going to grab power off an outlet. Does the power have to go into the switch box first and then out to the first light? and then on to the others? Can I get power from an outlet and then wire each of the lights and bring the last one to the switch box? I dont want the switch to control the outlet, just the recesed and I am trying to determine where I can get the power from and if it has to go into the switchbox? I am drawing a blank.

Thanks!