Cat5/coax

I recently switched over from AT&T phone/cable/Internet service to Cablevision. 



The problem with both services is the coax cable coming through a hole in the wall from outside and then a phone line from their modem stapled to the floor board and tied into the phone outlet inside.  Then there's my phone lines, the coax cable to the TV... It's a disgusting mess.



I'd like to install a combination phone line and cable outlet in the wall and get rid of as much loose wiring as possible.  The phone line would come through the same area as the cable and I'd wire it on the other end to the main box outside the house.



I have no experience with this so my question is can I take the phone line from the Cablevision modem and simply plug it into the outlet and get all the phones in the house to work or does it have to be hard wired or piggybacked inside the outlet?
      

I'm in the process of planning to wire up two spot lights on the face of my deck as well as running an outlet (which will also be under the deck) for a LV transformer to plug in to. I will need a few junction boxes to achieve this, as well as electrical boxes for the two spot lights. I'm planning on running 12AWG THWN through some sort of conduit run along the joists to the various lighting locations and junction boxes. This will be between 3' to 8' above the surface of the ground and under roof for the most part (we built a roof over the majority of the deck as well).



So, do you recommend PVC and plastic boxes or EMC and the appropriate boxes?
      

I want to run a Cat 5 line from my phone box outside to a jack inside to connect my phone and DSL. Right now I just have a regular phone line for both and the phone company recommends running a new line because the internet is always slow and I can't call out on my phone.



How do I know which wires to hook up outside?



Kevin
      

I just ordered some Arlington Siding Mount Kits with built in electrical boxes to install some lights on the outside of my garage. 



So, the issue is, the mount kits' built in electrical boxes are only 6.8 cu each and I'm wiring the lights up with two 3-way switches.  The source is at the first switch, then on to the two lights and then to the second switch.  There is not enough room to do the splices and connection in the built in boxes (I'm using 12awg, but even if used 14 still not enough room), so my plan was to wire everything to a central junction box inside the garage between the two lights and make the appropriate connections there. 



I'm attaching my rough sketch of the planned connections (omitting ground wires).  Can you guys please confirm this is correct?    Thanks for the help!



To clarify the drawing, blue is white (neutral) and the blue with black tape coming off second switch is marked as hot.  (I'll also mark it as hot in the J-box).  Yellow Triangles are wire-nuts.
      

I bought a portable car jumper and within the first 2 weeks of having it, the ac dc adapter fell out of the wall and the plastic casing on the adapter portion which plugs into the wall, broke.



I have priced replacing the ac dc adapter which at a minimum will cost me 30 dollars, or replacing the entire unit which will cost me about 80 dollars. I was planning on just using some electrical tape to cover up the opening, but I want to see if anyone else had some better ideas. Please see the attached picture and tell me what you think.



Obviously my concern is electric shock.




      

Hello All,

Hopefully I am posting this in the correct forum!

I am new to the forum and I have a question I would like to pose.

I am trying to make an extension cable for my telescope hand control.

I have had good results with the 25' length  but it is to short . So I made another one 50' in length but it give me connection error codes. The cable is correct as it worked for a while .I am using an rj12 6pin connector with cat5 cable(24awg). The power supply is 12V DC with 2.5 amps running on house AC.

The question is: If I put a different power supply on that is 12v DC using 5.0 amps will the increase in amperage effect the DC current flow?



Thanks,

Don
      

Ya know when your g/f or wife says, 'Don't you DARE talk down to me?'... well, I AIN'T your g/f or wife but what i IS is so DYI challenged that anything but the most basic explanation will cause my brain to short circuit.



To prove how DYI-tarded I am, I bought a used staking washer/dryer because it was what I could afford.. but now I can't plug it in. The plug is a large crows-foot deal but my outlets are standard USA deals.



I know it can't be as simple as changing the cord to a standard 3-prong.





KENMORE STACKING WASHER/DRYER  MODEL NO:  417.90802992

WASHER 120/240V

DRYER   240V

APPROX 4 YEARS OLD

EXCELLENT CONDITION



... the part number on the plug is E11808



Any suggestions (unless i starts with 'shove it up your') are appreciated.



Thank you - Mick
      

Is lowse electric fireplace reduce total heating costs better than home depot? Thanks



lowse 4600 BTU Electric Fireplace with Remote

Zone heating will help reduce total heating costs

No venting required

Electric fireplaces plug into a standard electrical outlet

Can be used with or without heat

and
Home Depot Electric Fireplace plugs into a standard 110-volt outlet and has a classic wood finish. It offers the cozy ambience of a real fireplace without the maintenance or venting requirements. This fireplace features a freestanding design and generates up to 4,600 BTU/hr heat output for rooms up to 1000 sq. ft

Plugs into any standard 110-volt electric outlet

up to 4600 BTU hr heat output for rooms up to 1,000 sq ft

Adjustable thermostatic control

Freestanding
      

I posted this in the woodworking forum and I got a ton of rants so please spare me that please. I'm not an idiot and I intend on completely turning off all power before attempting anything.



So I've been researching adding a couple of electrical outlets to my garage (where the panel is). I want to run a new 120v outlet for the tablesaw (older craftsman 113 series) so that it is on it's own circuit and a 240v outlet for a grizzly G1029z2 DC on it's own circuit as well.



What amp 120 circuit should I add for my tablesaw? Will a standard 15a breaker be fine?



What amp 240 circuit should I add for my DC? The motor plate states 12 amps and the manual says the electrical is a minimum circuit size of 20. Should I just install a 20amp circuit or go with larger circuit?



Need recommendations on the gauge of wire to use on each circuit.
      

Each time someone drives by my house using a cell phone it seems there is a one-time clicking noise coming out of several of my electrical outlets.  It may happen in all rooms at the same time but of course, the only ones I notice are in the room I am in currently.



Any ideas, and thanks!