Replacing 2-wire Cord On Old Motor

I was given a table saw from about 1960 - actually a very good machine - it would cost a fortune nowadays, but a friend who felt he owed me one gave it to me before he moved to Florida. It has a 1 HP motor that has always worked fine and has worked fine for me in tests, but the cord is an old 2-wire version, and I want to replace it with a new cord.



The manual says to use a 10 gauge wire (the cord is about 6' long). I want to replace it with a 3-wire, grounded cord. Do I simply run the neutral wire on the new cord where the old white wire was, the black wire to where the old black wire was, and connect the ground to the chassis?



The switch is a single throw, double pole switch, by the way.



Here's a link to the manual, if that helps anyone: http://vintagemachinery.org/pubs/detail.aspx?id=2007
      


Similar Tutorials

How to Lay Sod - The Right Way!
   - Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
   - This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
   - If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ...


Similar Topics From Forums

I spend alot of time outdoors and use my power tools or air compressor alot and use a 12 gauge contractors cord.  One problem I always have is that with my outdoor receptacle being above my deck sometimes the cord slips between the boards and hangs up and really causes a problem if the storm door is opened as it also catches the cord sometimes, and already damaged my other cord.



I am wondering if there are any issues with running the cord through pvc along the edge of the house and to the receptacle to protect it.



I am also wondering, since my old cord is damaged at one end, if rather than trying to repair it, if there is any code violation of running it into a weatherproof box and wiring it to a GFCI receptacle, reason I wonder this is that I have one on hand and have had no other use for it as I rent the house and cannot do any wiring to it, but it has no GFCI outlet which concerns me at times.
      
Hello everyone,I have a question about a forklift battery charger i bought. Ok,its an exide forklift battery charger 36 volts. It weighs a ton so i am having to run a 25 foot extension cord to it. My question is,my 220 wall outlet has three holes so i went to lowes and made a 220 extension cord. Now i get to the ac cable coming out of the charger that hooks to the extension cord(plug was cut off),there are 4 wires coming out of the cable green,white,red, and black......the guy at lowes said i could buy a 3 prong plug for it to plug into the female end of the extension cord because one of the 4 wires is probably neutral and i wouldnt have to hook up but the green,white and either the red or black.....is he right? Inside the charger the red,white and black all go to big fuses and green to ground. Also above the fuses it says "factory set to 480 volts ac". I guess my question is,will this charger only work using a 4 prong wall outlet(mine only has 3) and with 4 prong plug hooked to cable coming out of the charger itself or is the guy at lowes right in saying that only the red OR black wire has to be used? Sorry if this is confusing but ive searched and searched online for 3 days and havent found anything. Thanks in advance for any help-Kevin
      
I participate in a Pop-up camper discussion group (Popup Portal) and the following was posted reguarding the use of 30 amp extension cords:





"I just returned from Mobile Mart, my go to store for anything for my TT.  Was looking for a 25ft extension for my 30 amp power cord. The salesman  filled me in on some tips about buying extension cords for service.



1.  Never buy a black cord unless you have to have it now or it's the only  thing they have. The black cord absorbs and holds heat. We all know what  to much heat or amperage draw will do to an extension cord. Cords come  in a variety of colors.....orange, blue, yellow, etc. I picked up a  yellow one for visibility.



2. When your plugged in and have left  over cord DO NOT coil it up on the ground. Spread it out so any and all  heat can disipate easier. I usually pull just enough out to reach the  box and leave the rest inside the camper. I don't believe he was talking  about what is in the camper that but whatever is outside the camper  needs to be spread out.



3. If you have to have a lot of line  spread out to be able to plug in he suggested some type of covering to  shade the cord. I'm pretty sure this would pertain to monthly campers  and others that stay in one spot for awhile. Even still a good idea for  those of us that are down south here with temps in the triple digits."



I suggested that most (or all) of this is BS.



What say you?
      
I bought a Lincoln ac-225-S arc welder from someone and he gave me a 30' 10/3 extension cord with it.  The specs on the welder panel call for 50 amps max input on 20% duty cycle.  Is the 10 ga. wire really sufficient for this welder?  I will also be installing a receptacle for the welder, will a 30 amp breaker on 10/3 do the job or do I need to move up to 8 ga. on 40amp or 6 ga. on 50 amp?  If I go up to a 40 or 50 amp breaker can I even use that extension cord?  I doubt I would ever weld anything thicker than 3/16" to 1/4" max.
      
Hi.  This is not exactly home-improvement-related, but I'm hoping some of the electrical gurus out there can answer my question.  I am building an underwater fishing light.  It will basically be a sealed green acrylic tube with LED bulbs in it, powered by a 12V DC battery.  It will be submerged between 2-5 feet.  I imagine it will be used approximately between 2-6 hours at a time, so the cable will not be submerged in water or a wet area permanently. 



Obviously I am doing this to save $$ (they are expensive otherwise), and I find myself wondering why I can't buy an inexpensive extension cord (lamp-cord-style) and use it for the power from battery to light.  I started looking at garden lighting wire, but that stuff is very expensive.



Would auto electrical wire (with shrink tubing) be sufficient (though I'm not sure I can find shrink tubing with enough length)?  Speaker wire?  LOL. 



Any suggestions would be appreciated!



Edit: One thing I forgot to mention is that I don't want the power cord to be heavy at all.  Nice and light is the key!
      
how do i convert a 2 wire extention cord plug to a 3 way?
      
I have a LEM .35hp meat grinder that did not come with reverse. It is a PITA to use and not have reverse. It is a 120v 250w motor, w 2 caps. There is no schematic on the cover, so I have no idea what which wire goes to where. I plan on using a DPDT switch to reverse it. on-off-(on or mom) switch. I have attached pictures of the motor wiring.  White/black come in then go into motor. White comes out of motor then to larger cap, other wire from large cap goes to red (into motor). Red comes out of motor into smaller cap, second wire to small cab is blue going into motor.



http://i1086.photobucket.com/albums/...n/IMAG0021.jpg

http://i1086.photobucket.com/albums/...n/IMAG0020.jpg

http://i1086.photobucket.com/albums/...n/IMAG0022.jpg

Any help would be appreciated.
      
I have a small 19 gallon water heater in a small garage space, that was installed by some questionable handymen a few months back.  I just had the plumbing and septic finished so tested the hot water, only to find the element was already burned out.



I noticed however, that this 120v unit is wired via 10 gauge wire to a 30 amp double breaker.  This is questionable because I thought a 120v appliance would be wired to a single pole on the hot wire and run neutral to the neural panel area.



My question is, can I run the hot wire out of one side of the double breaker without safety issues, or should I definitely replace it with a single pole breaker?



I would normally not question the work, but everything these guys did already had to be adjusted, so I'm only naturally assuming this may need to be also.



If its safe, I would like to simply things and just connect the one hot and leave an open space in the other half of the double pole... Is this possible?



Thanks for your advice-
      
Am doing a bathroom reno and installed a new fan. Original switch was a simple on off single pole. I want to install a DewPoint condensation fan switch that will turn on automatically at a certain moisture level.

The new switch as 4 wires. green ground, red fan, black power, and white neutral. I know the ground, but how do I hook up the neutral and fan to the existing fan set up?

There is a double pole light switch in the same box that has a couple wires to it, and there is a mass of whites that I am not sure where they go



Can I hook up the neutral somewhere else, or put it with the fan like a single pole? What do I do with this?



In the attached picture the switch on the right is the 2 pole light switch and on the left is the fan switch that I hope to replace.



Your Advice is appreciated
      
I have an outdoor light fixture that I am trying to replace.  The house was built ten years ago.



When I removed the original lamp, I noticed one of the two leads was wired to the ground, and one was wired to the black wire, which is hot per my current sensor.  There are three wires in the box - black, ground (bare copper), and white or neutral, all from a single romex cable.  Unfortunately, I do not recall where the white was when I removed the original. 



I wired the new lamp per the instructions, something I have done many times before - black to black, white to white, and bare copper ground to ground.  Nothing.  The lamp and bulbs are brand new, and I have tried four separate bulbs.  I checked the black and neutral with my current sensor and with the switch on and the lamp installed this way, both show as hot. With the lamp not installed, the switch on, and the wires disconnected only the black shows as hot.  The switch is single pole, and appears to be wired correctly with a black to each screw on one side and a copper ground on the other.



Assuming the new fixture was bad, I reinstalled the old fixture correctly -  black to black, white to white, and bare copper ground to ground.  Still nothing. No light, and I confirmed the bulb is good by putting it in another lamp.   The only way to get it to light is to connect the neutral in the lamp to the bare copper ground.



I capped the wires, turned the circuit back on, and identified all the outlets, switches and fixtures on the same circuit.  I opened every one of them up (four lights and eight outlets) and found three (one switch and two fixtures in another room) where multiple commons connect.  All were properly connected.  My outlet tester shows all outlets as "correct".  I found no instances of grounds connected to commons or vice-versa.



Any ideas?  Is it proper to wire this thing the way I found it?



Thanks for any and all advice!