Dust To Dawn Timer For Led Outdoor Lighting?

Just bought some LED lights for the porch, but I realized the new digital timer in wall switch I purchased to replace the on/off says it's for incandescent only.  Been looking online, but couldn't find anything specific for LEDs, what should I use?



Thanks,
      


Similar Tutorials

How to Lay Sod - The Right Way!
   - Make sure the green side faces up! And, there are a few more steps if you want to ensure a nice looking lawn. Prepa ...
The Difference Between Volts, Amps, and Watts
   - This article explains the difference between Volts, Amps, and Watts in an easy-to-understand non-scientific way. T ...
Water is Leaking from the Toilet – What do I do? (How to replace the wax seal for a toilet.)
   - If there is water leaking from the toilet, you need to make sure that you know from where the water is leaking. Che ...


Similar Topics From Forums

I am trying to connect the Digital Timer switch to a 3 way switch. My issue is that the existing switch has 4 wires, Red, Black, White and Ground.



The Digital Timer has 5 wires, Red, Black, White, Blue and Ground (green). I can't understand how to connect it. Any help is appreciated.
      
I am trying to install a SunSmart Digital Timer to my hall lightswitch (single pole). The timer has 5 wires: Black, White, Blue, Red, and Green. My switch box only has 3 wires: Black, White, and the bare ground wire. I connected the black to the black, white to white, and green to the bare ground. I have power to the timer but the light doesn't work. What should I do with the blue and red wires? Right now I have each capped off. Thanks.
      
I installed an Intermatic brand programmable timer switch to operate some outside house lights (2 CFLs, total 30 watts). The thing worked for a few months and then became non-operational. I just realized that the sticker on the back of the timer switch states "max load ratings: 15 amp, 120 vac", and the circuit I installed it on is 20 amps. Is this why the switched failed? If so, why did it work for a few months? I thought 'load' was the amount of power needed to operate whatever is downstream of the switch, in this case my outside lights, which is under one amp?



Thanks!
      
I bought a Panasonic FV-13VKS3 vent fan. The fan is designed to run continuously at a preset lower level (e.g. 50CFM) that can then be elevated to its max level (130CFM) when switched on. When switched off, the fan has its own built-in, adjustable countdown timer that returns the fan back to the low setting.



What I would like to do is use a Leviton LTB30-1LZ to control the high fan level. For example, I would set the fan's built-in timer to 5 minutes. And when I switch on the LTB30 for 30 minutes, the fan will kick in to high mode for 30 minutes, then the LTB30 turns off and triggers the fan's built-in timer for an additional 5 minutes before returning to the low setting.



My question is, is this possible and how would I wire this?



Looking at the fan's wiring diagram, I think the two red wires from the fan would be used to switch the fan's built-in timer. But I'm unsure where to connect these two red wires onto the Leviton timer.
      
HI all,



I have a rain barrel system with a pump (110v) and I ran a 3way switch to my patio and one by the pump (in a shed).  My wife now wants the pump on a timer (to water the garden).



So...I could just add a timer to the switched outlet, but I want to be able to override the timer with the switch (at the patio or shed), without interfering with the pump timer operation.



I've drawn up a diagram showing my proposed setup.



Question: can I rig up the pump with two power cords and plug one into the timed outlet and one into the switched outlet and not burn down my shed in the process?




      
Greetings all.



This is my first post here, I hope it goes well.



My name is Joe and I have searched Google. and this forum for my answer but have not been able to find a definitive answer to my question.  I have seen many replies talking about getting a tone generator or a line tracer but my experience is that tone generators are for Data and phone cables rather than electrical cables and the line tracers I've found online all seem to be about tracing the line back to the breaker panel so without knowing more I'm hesitant to purchase a line tracer in case it cannot do what I want.

My dilemma is very likely very simple to anyone with electrical experience so I hope it's not too trivial for this crowd.

I have recently purchased a house that is over 120 years old and have a motion sensor light on the porch that is supposedly connected to a switch inside but does not turn on.  I've opened the wall plate and used a voltage indicating pen to see where the electricity is.  In this case there are two light switches, one that has lines that have been spliced and another that supposedly leads to the porch light according to a long time tenant in that unit.  It all looks like a bit of a mess and the connections don't make sense.  In this scenario the black cables have the electricity and the white cables complete the circuit.  The switch to the porch light has a black cable coming from the top of the box going to the switch and a white cable connected to the other screw that comes from splitting the white cable from the other switch.  What I would like to do is know which cables in that wall box correspond to the cables to the porch light.  Can anyone give me an idea what I should do?

Do I need something like the Amprobe advanced wire tracer (http://www.professionalequipment.com...0/wire-tracer/) and can it do what I need, or is there something simpler I can do?

All help is appreciated.

Thanks



Joe
      
Hi,



I need some help connecting a programmable electronic timer switch to an electronic door lock.  My goal is for the door to only unlock during a set period of time (when the timer is in the "on" position).



I have found two locks that I think may work, I just have no idea what wires to connect to what.



I attached three pictures.  Two of them are of the electronic timer (two different versions), and one is of the locking mechanism. 



Any help is greatly appreciated.
      
Looking for a way to automatically keep my two outdoor bulbs shut off during the day.  The timers seem to be on the expensive side and from what I read the screw-in sensors don't work very well.  Would appreciate some recommendations.

puttster
      
I want to run a new 12/3 to wire a room added on the back of the house. One circuit will be 6 wall outlets. The other will be a ceiling fan and 4 recessed cans. Can I add 2 outdoor lights-using standard outdoor bulbs-to the same circuit as the ceiling lights? Do I use the wall switch(box properly sized) as the junction for the outlet wiring and feed to wall switch for outdoor lights?
      
I'm planning to add some deck stair lighting this spring/summer to our newly finished deck, and knew I was going to go with low voltage. Then it had me thinking...I would also like to run low voltage in place of where we had originally planned to place solar lights along our sidewalk that's beside the deck (lights here will be embedded in river rock). Anyways, I know to steer clear of the HD and Lowe's brands, but I don't really know where to begin for quality lighting. I want the transformer to be rather large since it will have to handle larger runs, and be able to handle additional lights that may be added on down the road. Plus I want a timer/photo sensitivity built in. I was curious if anyone had any specific brands to recommend? I did see Kichler recommended in a few searches I made here, but any others?



Any general recommendations would be appreciated as well (i.e. buying a kit vs buying the transformer, wire, lights, connectors, etc. separate).